BMW M5 CSL prototype photographed in BMW’s garage

M-SHIFT ULTRA / THE CSL TUNE

An unfinished story.
A new chapter.

Custom MSHFT firmware with CSL Style Alpha-N for carbon-plenum setups without airflow meters. Inspired by BMW’s M5 and M6 CSL prototypes. Built around your original MSS65.

US$1,450 · Perpetual licence · One VIN

BMW M5 CSL prototype · Photo: BMW M · Prototype imagery, not a product performance claim

BMW M5 CSL prototype S85 V10 engine with carbon intake plenums
BMW M5 CSL prototype engine · Photo: BMW M · Explore the CSL prototypes ↗

CARBON PLENUMS / CSL ALPHA-N

The intake changes.
The firmware follows.

Ultra began with a clear goal: responsive CSL Alpha-N without the transient throttle lag we experienced with existing MSS65 Alpha-N calibrations. The original MSS65 firmware was designed around airflow meters. We developed Ultra’s custom firmware specifically for operation without them.

For a CSL-inspired carbon-plenum setup, Ultra brings that approach to your original MSS65 DME while retaining full knock control, adaptation and misfire detection.

CSL Alpha-NCustom MSS65 firmware
DCT · SMG · ManualSupported S85 configurations
Original MSS65S85 hardware and protection systems

WHAT ULTRA INCLUDES

A different approach
to the S85.

Purpose-built firmware for supported E60 M5 and E63/E64 M6 applications. CSL Alpha-N operates without airflow meters, with supported DCT, SMG and manual configurations.

Ultra currently includes a single performance calibration, developed for a more responsive feel than a stock S85 while retaining everyday drivability.

  • Custom MSHFT firmware for the standard MSS65 DME
  • CSL Alpha-N for supported S85 configurations
  • DCT integration and SMG III TCU tuning
  • Ultra-specific tools within M-Shift Studio for firmware, settings and diagnostics
  • One custom DCT calibration for DCT applications

ORIGINAL HARDWARE

Keep the S85’s
protection systems.

Ultra uses original MSS65 hardware rather than MSS60, retaining drivers for all ten cylinders and the S85 ionic knock system. Knock control, knock adaptation and misfire detection remain integrated.

When a cylinder misfire is detected, the DME can shut off that cylinder’s injector. Our approach prioritises smooth, predictable drivability and retains standard knock protection safeguards.

Dedicated software for your DME.

Load firmware, adjust supported settings, check adaptations, clear errors and calibrate the longitudinal sensor. M-Shift Studio also supports idle motor, throttle actuator and VANOS tests.

Some INPA and ISTA functions do not work with the custom firmware, so M-Shift Studio is required for those functions.

READ BEFORE PURCHASE

Installation is part of the decision.

Engine compatibility: Ultra is compatible only with naturally aspirated engines with standard camshafts and standard displacement.

Ultra firmware: installation and removal

Installation takes approximately 20 minutes. To remove the custom firmware, you must use M-Shift Studio. Do not overwrite it directly with standard DME firmware: this risks bricking the DME.

A DCT conversion requires an experienced installer who can read BMW wiring diagrams, diagnose faults, understand module interaction and code the vehicle independently.

You need a supported vehicle and hardware configuration, 64-bit Windows 10 or 11, a high-quality K+DCAN interface with EdiabasLib firmware and stable vehicle power.

A DCT calibration matched to your setup.

For DCT applications, one custom calibration is supplied at no additional charge, configured for tyre size and refined low-load operation and clutch take-up. Corrections for supported big-brake configurations are also available.

Separate DCT flashing licence required

A separate DCT Quick Flash licence is currently required to install the supplied DCT calibration. This is an additional requirement beyond the Ultra purchase.

General swap wiring, mechanical installation, routine coding and installation-fault diagnosis are outside the included support scope. A step-by-step DCT conversion guide and general swap pinouts are not included.

Rear aerodynamic detail of BMW’s M6 CSL prototype
BMW M6 CSL prototype · Photo: BMW M

PROTOTYPE THINKING

From BMW’s
experimental garage.

BMW explored a V10 paired with DCT in the M5 CSL prototype. The M6 CSL explored lightweight construction and active aerodynamics. These experimental cars inspire M-Shift’s approach to the S85.

TECHNICAL DETAILS

Understand the limitations.

CSL Alpha-N and throttle actuator failure

The S85 CSL Alpha-N setup has no MAP sensor for idle air-mass calculation. Low-load torque calculation differs from the S65 Alpha-N setup, and idle-motor-only limp-home operation is not available if the throttle actuators fail. The supplied DCT calibration refines low-load behaviour and take-up; it does not restore that fallback.

Instrument cluster displays

Park-symbol and launch-flag display depend on the cluster and coding. Suppressing a park-related error does not add those display features. Older clusters require custom firmware for full display behaviour; a straightforward OBD installation is not currently available.

Custom engine tuning

A custom engine-tuning service and open access to tuning tables are not currently included. Future tuning access is being explored and is not part of the current purchase.

CONFIGURE YOUR CSL TUNE

Settings for your build.

Ultra-specific tools are integrated into M-Shift Studio. After installing the custom firmware, open the Ultra tuning page from the Ultra menu to make engine tune changes and configure supported settings.

  • Stock, 599 or S65 injector calibration.
  • Engine-speed limit selection, oil-service interval and M-Drive defaults.
  • Transmission configuration, including a DCT final-drive ratio setting.
  • VMAX and supported SAP, EVAP, post-cat O₂ and primary-cat settings.
  • Cold-start delete is already included.

Confirm settings against the actual vehicle and transmission hardware.

Ultra installation and configuration →